Mold and mildew are the two problems Chattanooga homeowners notice first: black speckling in shower grout, a grey film on closet walls, dark streaks around window frames, or that musty smell in a back bedroom nobody uses. Mildew is a flat surface growth that wipes away. Mold has usually moved into the material itself. The difference matters because one is a cleaning job and the other needs removal, and guessing wrong means doing the work twice. We start by testing whether the growth lifts off the surface or has penetrated the drywall paper, grout, or wood behind it.
Hamilton County's summer humidity sits high enough for long enough that interior surfaces stay above the dew point only when air is moving. North-facing rooms, closets against exterior walls, bathrooms with an undersized or unvented fan, and rooms over an open crawl space are where we find most of it. In older homes around Brainerd, Highland Park and East Ridge, the original single-pane windows sweat all winter and the sills below them grow mildew every year. Newer homes are not immune: tightly sealed houses in Hixson and Ooltewah trap moisture indoors when bath fans vent into the attic instead of outside.
Our work covers both halves. Surfaces get HEPA vacuumed and cleaned, and anything porous that has been colonised comes out. Then we deal with why it happened: a bath fan that does not move enough air, a missing vapour barrier under the floor, a dryer vent discharging into a crawl space, grading that holds water against a wall. If the growth turns out to be more than surface deep, we tell you on the spot and move to full mold remediation with containment rather than cleaning over a problem. For growth under the floor or in the attic, see crawl space and basement mold removal and attic mold removal.
Technician insight
The thing that catches Chattanooga homeowners out with mildew is that it comes back in the same spot every single year, and they keep cleaning it instead of asking why that one wall is colder than the rest. Nine times out of ten it is a closet or bathroom on an exterior wall with no air movement, and a $300 fan or a vent redirected outside ends a problem they have been scrubbing for a decade.
Mold and Mildew Removal Services We Offer
✓Bathroom Mold and Mildew Cleanup
Grout, caulk, ceiling and extractor-fan cleaning, plus an airflow check so the room dries between uses instead of staying damp.
✓Closet and Wall Surface Mold
Treatment of mildew on drywall, baseboards and stored contents in closets built against cold exterior walls.
✓Window and Sill Mildew
Cleanup of condensation growth around frames and sills, common on the original windows in Chattanooga's pre-1970 housing stock.
✓Musty Odour Investigation
Tracing a musty smell to its source when nothing is visible, using moisture readings rather than guesswork.
✓Humidity and Ventilation Correction
Bath and dryer vent fixes, dehumidifier sizing and placement so indoor humidity stays in the range mildew cannot use.
Mold and Mildew Removal Cost in Chattanooga, TN
| Service | Typical Range | What Affects It |
|---|---|---|
| Single-room surface mildew cleanup | $250–$550 | Bathroom, closet or one wall. Includes moisture readings and ventilation advice. |
| Multi-room mold and mildew cleanup | $500–$1,200 | Depends on the number of rooms and how much contents handling is needed. |
| Surface cleanup with drywall replacement | $700–$1,800 | When the growth has gone through the drywall paper and a section has to be cut out. |
| Bath fan replacement or re-vent | $250–$600 | Correcting a fan that is undersized or discharging into the attic. |
Ranges are typical for Chattanooga, TN and confirmed with an exact written quote before any work starts.
How it works
- 1
Identify Mildew Or Mold
A technician tests whether the growth sits on the surface or has gone into the material, which decides whether this is a cleaning job or a removal job.
- 2
Find The Moisture Source
Moisture meter readings and an airflow check locate what is keeping the surface damp, whether that is a leak, condensation, or a vent discharging in the wrong place.
- 3
Clean Or Remove
Surfaces are HEPA vacuumed and treated. Porous material that has been colonised through is cut out and replaced rather than cleaned over.
- 4
Correct And Verify
The moisture problem is fixed, the area is dried, and we check readings before leaving so the same spot does not regrow next season.
Pricing
Surface mildew in one room is the lowest-cost job we do. Price rises when several rooms are involved, when material has to come out, or when a vent or drainage fix is part of the work.